Меню Закрыть

Windows setup ems enabled что это

Содержание

Здравствуйте дорогие читатели. Как известно в операционной системе Windows 7 существует полезная функция восстановления системы. Запустить её вы можете после загрузки с диска установочным Windows 7.

Восстановление системы хотя и не справится со всеми всевозможными проблемами, но основную часть из них решает автоматически.

Одна из причин по которой Windows 7 отказывается загружаться, это повреждение загрузчика Windows 7. В Windows XP он назывался boot.ini. Кстати восстановление загрузчика Windows XP вы можете выполнить при помощи этой статьи . А сегодня речь пойдет о восстановление загрузчика windows 7 как при помощи диска, так и без него. Главный признак, по которому вы можете понять что загрузчик Windows 7 поврежден, это когда при запуске семерки выскакивает ошибка — «BOOTMGR is missing. Press Ctrl+Alt+Del to restart».

1 Восстановление загрузчика windows 7

Первое, что в таком случае необходимо сделать это попытаться восстановить все как было, через точку восстановления. Запускаете восстановление системы Windows 7 и выполняете загрузку с последней точки восстановление. Подробней о точках восстановления Windows 7 можете почитать здесь .

Но как быть, когда точка восстановления не помогает а загрузка невозможна даже из под безопасного режима? Как выполнить восстановление загрузчика Windows 7? Вариантов несколько, начнем с восстановление системы Windows 7 — стандартными средствами.

В этом случае нам понадобится установочный диск (дистрибутив) Windows 7. Вставляем его в привод и загружаемся из под него. надеюсь вы помните, что для того чтобы загрузится с диска, необходимо выставить загрузку с диска через BIOS. На всякий случаю дам вам ссылку с описанием данной процедуры .

Далее. После того как загрузились с диска, появится окошко менеджера загрузки — выбираем [Windows Setup EMS Enabled].

Выбираем раскладку клавиатуры и ожидаем загрузки System Recovery Options.

Выбираем Startup Repair. После чего начнется анализ и устранение найденных ошибок Windows.

По идеи все автоматически будет исправлено. Если восстановление загрузчика Windows 7 не произойдет, то появится сообщение — Startup Repair could not detect a problem. Которое означает, что проблемы не были найдены.

В этом случае пойдем более проверенным способом — восстановление загрузчика Windows 7 через командную строку.

Снова загружаемся с диска, доходим до выбора операционной системы, выбираем её установив значение — Use recovery tools that can help fix problems starting Windows нажимаем next. Затем когда дойдет до окошка System Recovery Options выбираем командную строку — Command Prompt.

вводим в командной строке

bootsect /nt60 All

Если ввели правильно, то появится что-то вроде:


Нажимаем exit –> Enter

Вас должно перекинуть на System Recovery Options где мы выбираем Restart

Все. Система восстановлена.

После выполнения процедуры восстановление загрузчика Windows 7. Войдите в Windows и сделайте точку восстановления через Acronis, которую необходимо будет записать на жесткий диск. Таким образом вы сможете восстановить Windows 7 при возникновении любой непредвиденной проблемы. Читать подробней о восстановлении данных Acronis . Напоследок публикую 6-й тур по разгадыванию кроссвордов.

НАЧАТЬ РАЗГАДЫВАТЬ

На данный момент в турнирной таблице , можно выделить одного лидера это — Вадим. Вадим заработал больше всех баллов и по всей видимости не собирается сдавать позиции. Тем не менее остальные участники явно имеют не меньше шансов и они упорно стараются доказать это.

Так к примеру Dimson который совсем недавно подключился к участию в турнире в прошлый раз показал отличный результат. Обогнал всех и получил 10 баллов — что тут скажешь, парень молоток. Желаю ему успехов в дальнейшем.

Так же незабываем, что по окончанию турнира будет 10 призовых мест, то есть 10 участников которые соберут больше остальных баллов за разгадывание кроссвордов гарантированно получат денежное вознаграждение. Подробней об условиях турнира .

Читайте также:  Схема подключения двух вызывных панелей к домофону

Кроме того, в конце месяца будут определены 3-е самых активных комментатора, которые также не останутся без вознаграждения за участия в дискуссиях на этом блоге. Подробней тут .

Emergency Management Services (EMS) technology allows you to control the selected components of servers remotely, even when a server is not connected to the network or to other standard remote-administration tools. EMS is supported on all versions of Windows Server 2003 operating systems for x86-, x64-, and Itanium-based computers.

This topic explains how to enable EMS on computers running Windows Server 2003. The boot parameters described in this section are not supported on Windows Vista or later versions of Windows. When a boot entry is configured for EMS on a computer with BIOS firmware, the boot loader appends a bracketed phrase, [ems enabled], to the friendly name that appears on the boot menu. However, the boot loader omits the bracketed phrase from the boot menu when the friendly name and the bracketed phrase together exceed 70 characters. To restore the bracketed phrase, shorten the friendly name.

To determine whether a computer has ACPI firmware, use Device Manager (devmgmt.msc). In Device Manager, expand the Computer node. On computers with ACPI firmware, the name of node under Computer includes the word, ACPI.

Enabling EMS on a computer without an ACPI SPCR table in operating systems prior to Windows Server 2008

To enable EMS console redirection on a computer that has BIOS firmware, but does not have an ACPI Serial Port Console Redirection (SPCR) table, add the redirect=COMx and the redirectbaudrate= parameters to the [boot loader] section of the Boot.ini file. These parameters set the port and transmission rate for EMS console redirection. Use the same port and transmission rate that are established for out-of-band communication in the BIOS. Then, add the /redirect parameter to a boot entry.

The following Bootcfg command enables EMS console redirection on the first boot entry in the list. It sets the port for COM2 and sets the transmission rate to 115,200 kilobits per second (Kbps). These are the same port and baud rate settings that the administrator set in the BIOS for the out-of-band port.

The following Bootcfg display shows the result of the command. The newly added parameters are displayed in bold type.

The following sample shows the result of the same command on a sample Boot.ini file.

Enabling EMS on a Computer without an ACPI SPCR Table in Windows Server 2008

To enable EMS console redirection on a computer that has BIOS firmware, but does not have an ACPI Serial Port Console Redirection (SPCR) table, use the BCDEdit /emssettings command to set the COM port and baud rate.

These parameters set the global port and transmission rate for EMS console redirection. Use the same port and transmission rate that are established for out-of-band communication in the BIOS.

Then, use the BCDEdit /ems command to enable EMS for a boot entry.

The following commands set the global EMS redirection settings to use COM2 and a baud rate of 115200, and enable EMS for the specified boot entry.

Enabling EMS on a computer with an SPCR table in operating systems prior to Windows Server 2008

To enable EMS on a computer with ACPI BIOS firmware and an ACPI SPCR table, you can either use the redirect=USEBIOSSETTINGS parameter or the redirect=COMx and redirectbaudrate= parameters. Then, you can add the /redirect parameter to a boot entry.

Читайте также:  Exception einouterror in module

The following example demonstrates use of the redirect=USEBIOSSETTINGS parameter. The following Bootcfg command enables EMS console redirection on the first boot entry in the list.

The following Bootcfg display shows the result of the command. The newly added parameters are displayed in bold type.

The following sample shows the result of the same command on a sample Boot.ini file.

Enabling EMS on a Computer with an SPCR Table in Windows Server 2008

To enable EMS on a computer with ACPI BIOS firmware and an ACPI SPCR table, you can use the BCDEdit /emssettings and specify either the BIOS parameter or the emsport and emsbaudrate parameters. To enable EMS for a boot entry, use the BCDEdit /ems command.

The following example demonstrates how to use the BIOS parameter. The following BCDEdit command enables EMS console redirection on the current boot entry.

Enabling EMS on a computer with EFI firmware in operating systems prior to Windows Server 2008

To enable EMS on a computer with EFI firmware, use Bootcfg to add the /redirect parameter to a boot entry. Windows finds the out-of-band port and its settings in the firmware by reading the SPCR table and uses the same port and rate for EMS console redirection.

The following Bootcfg command enables EMS redirection on an Itanium-based computer. It uses the Bootcfg /ems switch with the ON argument to add the /redirect parameter to the boot entry. The /id switch identifies the boot entry.

The following Bootcfg display of boot options in EFI NVRAM shows the result of the Bootcfg command. The first boot entry is configured to load the operating system with EMS console redirection enabled.

Enabling EMS on a Computer with EFI Firmware in Windows Server 2008

To enable EMS on a computer with EFI firmware, use the BCDEdit /ems command and specify a boot entry. Windows finds the out-of-band port and its settings in the firmware by reading the SPCR table and uses the same port and rate for EMS console redirection.

The following command enables EMS console redirection on the specified boot entry that has the identifier of <18b123cd-2bf6-11db-bfae-00e018e2b8db>.

Changing EMS Settings on a Computer with BIOS Firmware in Operating Systems prior to Windows Server 2008

When you configure EMS on a single boot entry, add the redirect= parameter to the [boot loader] section of the Boot.ini file. However, when you enable EMS on additional boot entries, you do not need to add the redirect= parameter again. Like all entries in the [boot loader] section, redirect= (and redirectbaudrate=) applies to all boot entries on the computer.

The following Bootcfg command enables EMS on the second boot entry. Because the port and baud rate are already set, there are no /port or /baud switches in the command.

To change the port and baud rate settings, use the Bootcfg /ems switch with the EDIT argument. The following command changes the EMS port to COM1 and changes the baud rate to 57,600 Kbps.

To disable EMS on a boot entry, use the Bootcfg /ems switch with the OFF argument. The following command disables EMS on the first boot entry.

If EMS is not enabled on any other boot entries, Bootcfg also deletes the EMS port and baud rate settings from the [boot loader] section of the Boot.ini file.

Читайте также:  Разные интервалы между словами в ворде

Changing EMS Settings on a Computer running Windows Server 2008

When you configure EMS on a boot entry on a computer that has ACPI BIOS firmware and an ACPI SPCR table, you can use the BCDEdit /emssettings command and specify either the BIOS option or the emsport and emsbaudrate options. If you use the BIOS option, do not set the emsport or emsbaudrate options.

When you configure EMS on a computer that has EFI firmware, or with ACPI BIOS firmware and without an ACPI SPCR table, you can use the BCDEdit /emssettings command and specify the emsport and emsbaudrate options.

The emsport and emsbaudrate options set the serial port and transmission rate for EMS console redirection. These settings apply to all boot entries on the computer. To use emsbaudrate, you must also set the emsport option. By default, the transmission rate is set to 9600 (9,600 Kbps).

For example, the following command changes the EMS port to COM2 and changes the baud to 57,600 Kbps.

To enable or disable EMS on a boot entry, use the BCDEdit /ems command.

For example, the following command enables EMS on a specific boot entry that has an identifier of <173075c9-2cb2-11dc-b426-001558c41f5c>..

To disable EMS on the current boot entry, use the following command.

Each boot entry uses a GUID as an identifier. If you do not specify an identifier, the BCDEdit command modifies the current operating system boot entry. If a boot entry is specified, the GUID associated with the boot entry must be enclosed in braces . To view the GUID identifiers for all the active boot entries, use the bcdedit /enum command.

Эта команда позволяет изменить конфигурацию перенаправления консоли Emergency Management Services (EMS) (Windows Server 2003) на удаленный компьютер. При запуске этой команды в заголовок [boot loader] вставляется запись redirect-Port#.

Кроме того, к записи указанной операционной системы в разделе [operating systems] добавляется параметр /redirect.

Вот синтаксис команды bootcfg /ems:

Параметры команды рассматриваются в следующей таблице.

Параметры команды bootcfg /ems

Включает удаленный вывод для указанного экземпляра операционной системы. Экземпляр указывается с помощью значения параметра /id. При использовании этого параметра к указанному экземпляру операционной системы добавляется параметр /redirect, а параметры перенаправления добавляются в раздел [boot loader]. Параметры перенаправления устанавливаются в зависимости от значения параметра /port

Отключает удаленный вывод EMS для выбранного экземпляра операционной системы

Позволяет изменить текущие параметры порта EMS (устанавливаются с помощью параметра /port) для указанной операционной системы

Этот параметр необходим для указания экземпляра операционной системы в файле boot.ini, к которому применяется команда. Нумерация этого экземпляров для этого параметра начинается с 1, поэтому для применения команды для второй операционной системы, описанной в разделе [operating systems] файла boot.ini, необходимо воспользоваться параметром /id 2. Отношение номеров и экземпляров операционной системы можно узнать с помощью команды bootcft /query

Указывает номер порта, который должен использоваться для перенаправления. Допустимы следующие названия последовательных портов: COM1, COM2, COM3, COM4 или BIOSSET. Если в качестве названия последовательного порта указано значение BIOSSET, EMS получает действительный последовательный порт от BIOS компьютера

Указывает скорость передачи, которая будет использоваться для перенаправления. Этот параметр поддерживает такие допустимые значения: 9600, 19200, 38400, 57600, 115200

Для использования команды bootcfg с целью включения EMS (через последовательный порт COM1 на скорости 115200) для операционной системы Windows Server 2003 (первая операционная система в списке) необходимо воспользоваться следующей командой:

Рекомендуем к прочтению

Добавить комментарий

Ваш адрес email не будет опубликован.