Replace printheads indicated by flashing

Вопрос:

Здравствуйте. Помогите, пожалуйста с такой проблемой. Два месяца назад "Error. select replace printheads" было на magenta — заменил. Напечатал 5 или 6 полноцветных А1 и столько же просто текстов чёрным цветом — полный порядок. Теперь эта ошибка указывает на Black. Перед этим распечатал плакат со странными полосками от каждой буквы. Вопрос следующий: просто заменить и эту головку или проблема в каретке (эти головки ведь рядом стоят).
P.S. Контакты прочищал и на головке и в каретке — не помогло. Спасибо.

Ответ:

По-видимому, пришел срок замены головок, и скорее всего вам в ближайшем будущем понадобится заменить их все.

Задайте свой вопрос

© 2017г. АльфаТех плюс, все права защищены

Помогите нам стать лучше. Оставьте отзыв на Яндекс.Маркете и Фламп

Flashing X on the yellow toner on display. error message reads Replace printhead

Posted by Anonymous on Jan 09, 2014

3 Suggested Answers

6ya staff

• 2 Answers

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Instant Repair Help over the Phone

Save Time & Money by instantly connecting to.

Posted on Jan 02, 2017

Anonymous

• 39 Answers

Stape :: 1
Your Printer Cover Open Few Minitus

Stape :: 2
Plz Chek Your Printer Property . And Delete Your Own Page

Stape :: 3 Plz Check Printer Property And Port Tab Chenge Selected Port

Posted on Aug 17, 2009

Tim Grayson

• 2777 Answers

The print-head sensor has failed from the sounds of it. I assume you have tried resetting the printer by unplugging it and letting it sit a good 30 seconds, then replugging it? Still showing bad? Unfortunately the printer at that point needs to be repaired or replaced :(.

Posted on Sep 29, 2010

Add Your Answer

Tips for a great answer:

• — Answer the question.
• — If you need clarification, ask it in the comment box above.
• — Better answers use proper spelling and grammar.
• — Provide details, support with references or personal experience.

Draw a box over the problem!!

Attachments: Added items

Complete. Click "Add" to insert your video. Add

Related Questions:

I am getting an error telling me to replace all 4 print heads. I thought it was odd that all 4 would go out at the same time. Should i replace all 4 print heads or is the problem something else? Maybe

This is general problem in hp plotters..
understand the concept: If U R replaced any one of print head in good working printer, printer detects new print head & it will try to align it with others. Printer will print align page to read, while reading if its found any other print heads are poor quality or bad condition, it will say to replace them also.. Some times it may 2,3 or all.
If UR printer is trying to printing align page and reading it, definitely it will detects & displays the faulty /poor quality print heads. U have to replace it..
If UR feels its expensive, try to clean the print heads manually & try for UR luck.
Trailing cable error is 11:11.

Hp designjet z2100 keep asking to replace the feed heads of magenta and yellow even after replacement and print block of magenta + yellow.

86:01 error in designjet 500 plus Paper jam.

According to the HP website the printer is a HP Designjet T1200 44" PostScript Version Printer. I installed a new yellow ink cartridge (72)after the original cartridge ran out. The printer is giving.

HP Designjet 500 24-in Roll Printer error message 2110

Service Station failure. The possible cause could be:
The steps counted by the Service Station motor are not consistent with the expected length of the current movement.
The Aerosol Fan has reached its maximum current limit.
The Service Station motor has shutdown because of blockage.

Corrective Action Try the following:
Remove ALL the Printheads and clean the flex contacts on the Printheads and in the Carriage Assembly.
Replace ALL the Printheads.
Replace the Service Station/Aerosol Fan Assembly

HP 800 designjet plotter Error Message 21:10

HP Designjet 4000ps printhead error

Stape :: 1
Your Printer Cover Open Few Minitus

Stape :: 2
Plz Chek Your Printer Property . And Delete Your Own Page

Stape :: 3 Plz Check Printer Property And Port Tab Chenge Selected Port

My 3 printhead (yellow,magenta & cyan) on the HP designjet 1050c machine have status — replace 20,replace 20 & replace 21, respectivly. How to do to not change them now, but to do like that — to.

Hp designjet 1050c printer displays a system error

Hi,
Printhead failure this is.

Turn the printer on.
Following initialization,
use the Down Arrow key to scroll to the Ink system menu icon and press Enter.
NOTE:If the error code appears during initialization press the Enter
key to allow printer to complete the rest of the initialization process.
Scroll to Replace Printheads and press Enter.
The printer should now move the carriage to an accessible position.
Open the top cover.
Remove all four printheads.
Turn the printer off using the main power switch located on the back of the printer.
Turn the printer on.
Following initialization, insert one printhead at a time, starting with the black printhead.
Determine whether or not the printer accepts the printhead.
Turn the printer off and repeat steps for each of the printhead.
Replace the failed printhead.